Target Sprint

Sort By:  
Foresight Blocks (Replacement) Air Arms
Replacement Foresight blocks for Air Arms standard Foresight element tunnel. These are a direct replacement for broken Air Arms blocks.
£2.00
Dry Fire Adaptor - MPR S400 TS400
When dry firing your MPR you need to unscrew and release the air from the chamber and leave the cylinder loose. The MPR air cylinder is then unstable and when moving the rifle the balance can feel different to normal. Using the Dry Fire adaptor means you release the air from the chamber by unscrewing the cylinder enough to insert the adaptor, check that the barrel is clear and then insert the adaptor. Once the adaptor is inserted tighten the cylinder. At this point the cylinder is tight but the air is not released to the rifle chamber allowing dry fire but also the cylinder no longer moves. Note: Colour May Vary.
£0.50
Slide on Blinder - Pair
Two Blinders to Slide/Clip onto std Air Arms, BSA or similar Dioptre Sights with 8mm thread.

Choose Colour before adding to Basket. Options are Opaque, White, Black.
Black is often used for Bright Sunlight e.g. in Targetsprint to avoid glare from the Opaque/white.

Complies with ISSF Rule [7.4.1.3.4.1] & Sporter rules.The centre point of the Dioptre to edge of these Blinders is approx 90mm, and the width is 29.5mmRules allow for100mm and 30mm Wide.

Why use a Blinder
By closing one eye it is understood to impair the ability to judge depth and distance.You also cause the open eye work to harder which can lead to eye strain. Closing one eye can also affect your balance.For these reasons using a blinder can assist in improving your shooting. Some shooters choose to use a blinder to force the use of the non dominant eye in preference to holding the rifle / pistol in a preferred hand.These blinders are also suitable to be used with a headband. You can either place the holed end under the headband or affix some velcro.

Instructions on use
Holding the blinder with the opening away from you. Place a finger into center of blinder just below the hole, push down with this finger whilst holding the sides to create a slight curve, Then slide onto diopter. Small cracking sounds maybe heard on first few applications. Use same process to remove. Use Caution if turning blinder from one side to the other due to the clip on design the opening may catch on the edge of the diopter housing.Following these guidelines should result in many uses. (Random tests have allowed for min 200 uses although this may vary dependent on use}(Note this is for the Blinder Only, the dioptre sight shown is for illustration purposes only)

Alternative
Just cut out from a plastic milk bottle, just may not look as nice.
£3.00
Breach Insert - MPR
Breach Insert for Air Arms MPR S400 Rifle.

This has been a winning choice for Target Sprint athletes to enable faster loading of the rifle without missing the breach and overthrowing the pellet.

As with the insert for the TS400 this also covers the bolt when the bolt is retracted avoiding the placing of the pellet on top of the bolt.

This is friction mounted to the rifle by positioning flat over the breach and pushing down vertically. Then easily removed by following this in reverse.

Can be ordered with Right or Left opening. Specify before adding to basket.
£5.00
Breach Insert - TS400
Breach Insert for the Air Arms TS400 Targetsprint Rifle.

This has been a winning choice for Target Sprint athletes to enable faster loading of the rifle without missing the breach and over throwing the pellet.

Comments were made that the pellet groove appeared shallower in the TS400 compared with the MPR so the addition of the small arm on this version of the breach insert makes the pellet groove deeper allowing for a better seating of the pellet.

The breach is also slightly smaller on the TS400 compare with the MPR.

As with the insert for the MPR this also covers the bolt when the bolt is retracted avoiding the placing of the pellet on top of the bolt.This is friction mounted to the rifle by positioning flat over the breach and pushing down vertically. Then easily removed by following this in reverse.

Can be ordered with Right or Left opening. Specify before adding to basket.
£5.00
Pellet Holder V4 MPR and TS400 - With Removable Plate
This is a V4 Pellet holder designed for the Air Arms MPR or TS400 Rifles.

Plate Size approx 7.5 x 7.5 cm big enough to hold 20 to 30 pellets evenly spaced.

A Pellet holder is an essential tool in Targetsprint affixed to the rail mount forward of the breach allowing for a quick pickup of pellets from the plate of the pellet holder to insert into the breach with the smallest amount of movement. The time saved by loading from a pellet holder to picking your pellet from the rifle stand is essential is you want to improve upon your time.

The pellet holder slides onto the rail mount forward of the breach and is secured by tightening the 2mm Allen screw. It is only the pellet holder that is supplied the means of holding the pellets is not. 
This can be achieved with either Double sided sticky tape or my preference stickyback craft foam with 4mm holes punched into it.

Pellet holders like this are used by the GB Team and the German teams, this is a must have item for a serious target sprinter!

Will also fit S200 although not designed specifically for this rifle
£15.00
Pellet Holder V1 MPR and TS400
This is a V1 Pellet holder designed for the Air Arms MPR or TS400 Rifles.

Plate Size approx 8.5cm x 4.5cm

A Pellet holder is an essential tool in Targetsprint affixed to the rail mount forward of the breach allowing for a quick pickup of pellets from the plate of the pellet holder to insert into the breach with the smallest amount of movement. The time saved by loading from a pellet holder to picking your pellet from the rifle stand is essential is you want to improve upon your time.

The pellet holder slides onto the rail mount forward of the breach and is secured by tightening the 2mm Allen screw. It is only the pellet holder that is supplied the means of holding the pellets is not. 
This can be achieved with either Double sided sticky tape or my preference stickyback craft foam with 4mm holes punched into it.

Pellet holders like this are used by the GB Team and the German teams, this is a must have item for a serious target sprinter!

Will also fit S200 although not designed specifically for this rifle
£10.00
Sight Riser
Sight Riser - Select Height
Sight Riser for 11mm width rail suitable for Air Arms MPR, S200 and other rifles with 11mm rails. Printed to required Height and colour, select from dropdowns before adding to cart. The Rear Mount is 65mm Long and has 2 x Securing Points. The foresight is 10mm ling and has 1 x securing point. The risers slide onto the 11mm rail and are secured by tightening the 2mm allen screws. When ordering please specify the sizes required. These will fit Air Arms MPR and other Similar Rifles. Note: Rules state Centre of Dioptre to Centre of Barrel max 60mm. Air arms MPR max height is 33mm sight riser.
£10.00
Rain Cap for Barrel and Foresight Element
The Barrel and foresight element endcap/cover has been designed for those rainy, snowy shooting sessions outdoors in particular for target sprint. Whilst running each of your 400m laps the foresight element and the barrel can collect water. The Rain cap works with gravity unlike other brands where the shooter is required to snap the cover into the closed position before storing the rifle in the rack and then snap back into the open position before shooting eating up valuable seconds and affecting your overall time. The item is fixed onto the rifle using a single cable tie around the muzzle behind the foresight block. This design was used at the British Shooting National Series competition 2019. You will need to provide a measurement for the cover length when ordering which is from the bottom of the muzzle to the top of the foresight element this is to ensure that your cap fits to your rifle setup with or without sight risers. I will add a couple of MM to this to ensure full coverage. Please note this will NOT fit to the Air Arms Precision Style muzzle only the Sporter style muzzle as shown in the images.
£3.00
Sight Riser
BSA Silver Star Sight Riser - Select Height
Sight Riser for BSA Silver Star. Printed to required Height and colour, select from dropdowns before adding to cart. The Rear Mount is 65mm Long and has 2 x Securing Points. The foresight is 10mm ling and has 1 x securing point. The risers slide onto the 11mm rail and are secured by tightening the 2mm allen screws. When ordering please specify the sizes required. These will fit Air Arms MPR and other Similar Rifles. Note: Rules state Centre of Dioptre to Centre of Barrel max 60mm.
£10.00
Pellet Holder V5 BSA Silver Star - With Removable Dual sided Plate
This is a V5 Pellet holder design for the BSA Silver Star Rifle. This pellet holder is not able to be personalised as it is ambi fitting. Meaning it is ideal for clubs. in that it can be fitted to the left of the right side of the rifle, both sides of the pellet holder are flat to hold the foam or sticky tape for holding the pellets.

Plate Size approx 7.5 x 7.5 cm big enough to hold 20 to 30 pellets evenly spaced.

A Pellet holder is an essential tool in Targetsprint affixed to the rail mount forward of the breach allowing for a quick pickup of pellets from the plate of the pellet holder to insert into the breach with the smallest amount of movement. The time saved by loading from a pellet holder to picking your pellet from the rifle stand is essential is you want to improve upon your time.

The pellet holder slides onto the rail mount forward of the breach and is secured by tightening the 2mm Allen screw. It is only the pellet holder that is supplied the means of holding the pellets is not. 
This can be achieved with either Double sided sticky tape or my preference stickyback craft foam with 4mm holes punched into it.

Pellet holders like this are used by the GB Team and the German teams, this is a must have item for a serious target sprinter!
£15.00
Per Page      1 - 11 of 11
  • 1

About

I am a qualified NSRA County Coach for both air rifle and pistol and regularly invovled in coaching local scouts and the Scout National Squad members. I am also involved in Target Sprint and currently an Educator for British Shooting. 
I started 3d printing when the cost of sight risers in particular seemed to be out of the price range for most beginner shooters. Sight risers being an important aspect in achieving a good position in shooting. Suggestions then came in about other products which have been developed with the input of shooters from many backgrounds some of which have also competed for GB.
If the items you are looking for are not on sale here then please to email me with a sketch and dimensions of your idea and I will gladly look into designing it for you. 
My printing is limited in size however so we are looking at smaller items within a size of 200x200x200mm. 
I am able to print in PLA, PETG and ABS and hold stock of a few colours, if the colour is not listed I may be able to purchase this for your project or Item.