Rifle
Rifle Accessories
Plate Size approx 7.5 x 7.5 cm big enough to hold 20 to 30 pellets evenly spaced.
A Pellet holder is an essential tool in Targetsprint affixed to the rail mount forward of the breach allowing for a quick pickup of pellets from the plate of the pellet holder to insert into the breach with the smallest amount of movement. The time saved by loading from a pellet holder to picking your pellet from the rifle stand is essential is you want to improve upon your time.
The pellet holder slides onto the rail mount forward of the breach and is secured by tightening the 2mm Allen screw. It is only the pellet holder that is supplied the means of holding the pellets is not.
This can be achieved with either Double sided sticky tape or my preference stickyback craft foam with 4mm holes punched into it.
Pellet holders like this are used by the GB Team and the German teams, this is a must have item for a serious target sprinter!
Will also fit S200 although not designed specifically for this rifle
This has been a winning choice for Target Sprint athletes to enable faster loading of the rifle without missing the breach and over throwing the pellet.
Comments were made that the pellet groove appeared shallower in the TS400 compared with the MPR so the addition of the small arm on this version of the breach insert makes the pellet groove deeper allowing for a better seating of the pellet.
The breach is also slightly smaller on the TS400 compare with the MPR.
As with the insert for the MPR this also covers the bolt when the bolt is retracted avoiding the placing of the pellet on top of the bolt.This is friction mounted to the rifle by positioning flat over the breach and pushing down vertically. Then easily removed by following this in reverse.
Can be ordered with Right or Left opening. Specify before adding to basket.
This has been a winning choice for Target Sprint athletes to enable faster loading of the rifle without missing the breach and overthrowing the pellet.
As with the insert for the TS400 this also covers the bolt when the bolt is retracted avoiding the placing of the pellet on top of the bolt.
This is friction mounted to the rifle by positioning flat over the breach and pushing down vertically. Then easily removed by following this in reverse.
Can be ordered with Right or Left opening. Specify before adding to basket.
Choose Colour before adding to Basket. Options are Opaque, White, Black.
Black is often used for Bright Sunlight e.g. in Targetsprint to avoid glare from the Opaque/white.
Complies with ISSF Rule [7.4.1.3.4.1] & Sporter rules.The centre point of the Dioptre to edge of these Blinders is approx 90mm, and the width is 29.5mmRules allow for100mm and 30mm Wide.
Why use a Blinder
By closing one eye it is understood to impair the ability to judge depth and distance.You also cause the open eye work to harder which can lead to eye strain. Closing one eye can also affect your balance.For these reasons using a blinder can assist in improving your shooting. Some shooters choose to use a blinder to force the use of the non dominant eye in preference to holding the rifle / pistol in a preferred hand.These blinders are also suitable to be used with a headband. You can either place the holed end under the headband or affix some velcro.
Instructions on use
Holding the blinder with the opening away from you. Place a finger into center of blinder just below the hole, push down with this finger whilst holding the sides to create a slight curve, Then slide onto diopter. Small cracking sounds maybe heard on first few applications. Use same process to remove. Use Caution if turning blinder from one side to the other due to the clip on design the opening may catch on the edge of the diopter housing.Following these guidelines should result in many uses. (Random tests have allowed for min 200 uses although this may vary dependent on use}(Note this is for the Blinder Only, the dioptre sight shown is for illustration purposes only)
Alternative
Just cut out from a plastic milk bottle, just may not look as nice.
Plate Size approx 7.5 x 7.5 cm big enough to hold 20 to 30 pellets evenly spaced.
A Pellet holder is an essential tool in Targetsprint affixed to the rail mount forward of the breach allowing for a quick pickup of pellets from the plate of the pellet holder to insert into the breach with the smallest amount of movement. The time saved by loading from a pellet holder to picking your pellet from the rifle stand is essential is you want to improve upon your time.
The pellet holder slides onto the rail mount forward of the breach and is secured by tightening the 2mm Allen screw. It is only the pellet holder that is supplied the means of holding the pellets is not.
This can be achieved with either Double sided sticky tape or my preference stickyback craft foam with 4mm holes punched into it.
Pellet holders like this are used by the GB Team and the German teams, this is a must have item for a serious target sprinter!
Plate Size approx 8.5cm x 4.5cm
A Pellet holder is an essential tool in Targetsprint affixed to the rail mount forward of the breach allowing for a quick pickup of pellets from the plate of the pellet holder to insert into the breach with the smallest amount of movement. The time saved by loading from a pellet holder to picking your pellet from the rifle stand is essential is you want to improve upon your time.
The pellet holder slides onto the rail mount forward of the breach and is secured by tightening the 2mm Allen screw. It is only the pellet holder that is supplied the means of holding the pellets is not.
This can be achieved with either Double sided sticky tape or my preference stickyback craft foam with 4mm holes punched into it.
Pellet holders like this are used by the GB Team and the German teams, this is a must have item for a serious target sprinter!
Will also fit S200 although not designed specifically for this rifle
Plate Size approx 7.5 x 7.5 cm big enough to hold 20 to 30 pellets evenly spaced.
A Pellet holder is an essential tool in Targetsprint affixed to the rail mount forward of the breach allowing for a quick pickup of pellets from the plate of the pellet holder to insert into the breach with the smallest amount of movement. The time saved by loading from a pellet holder to picking your pellet from the rifle stand is essential is you want to improve upon your time.
The pellet holder slides onto the rail mount forward of the breach and is secured by tightening the 2mm Allen screw. It is only the pellet holder that is supplied the means of holding the pellets is not.
This can be achieved with either Double sided sticky tape or my preference stickyback craft foam with 4mm holes punched into it.
Pellet holders like this are used by the GB Team and the German teams, this is a must have item for a serious target sprinter!
The item is made up of 4 parts
2 x Bolts & Nuts
1 x Stand Collar (Enter Pole Diameter when adding to basket)
1 x Pellet Tray holder.
This is an essential part of range equipment particularly for the standing rifle shooter.
The stand is used to rest the rifle on when loading, the pellet tray holder ensures that the pellets are in easy reach.
The holder is designed for the many pellet trays that exist to fit into, or alternatively hold a tin of pellets in easy reach of the shooter.The design allows for the tray to be removed when storing leaving the collar in place on the stand.Can be personalised at no extra cost.
- 1